Minuteman SCV2832E Wartungshandbuch

Service ManualFor the SCV2832E, SCV2426, SCV280000 & ES2832SCV280000 & ES2832 Automatic ScrubbersFor:oTrainingTroubleshootingAdjustmentsAdjust

3. Service ModeThe Service mode switch can be used to lower the brush deck.Press and hold the switch in the down position and the deck will lower. On

3.1 Service Mode SC280000Push and hold the brush pressure down button for 15-20 seconds.1520 seconds.Once it is in service mode, You can raise and lo

3.2 Service Mode SCV2426The Service Mode Switch on the SCV2426 is located next to the step on the front of the machine on the operator’smachine on the

4. Brush Pressure SettingsThe brush pressure range can be changed when changing the type of deck on the SC2832E, SC2426P, CP2832 and ES2832 models. Co

4.1 ES2832,CP2832, and Phoenix 34It is now available to change the brush pressure settings in the field, when changing brush decks on current producti

4.2 ES2832,CP2832, and Phoenix 34Locate the Red/Black wire group Locate the Orange/Violet wirePage 15 g

5. Error CodesThe model SC280000 Rider scrubber uses a LCD display mounted above the steering wheel which indicates the error code when they occur. T

6. Table of Error CodesCode Information or Fault Description Comments and Corrective Action0810 TILLER FAULT-1 For a

6. Table of Error Codes2C00 LOW BATTERY ERROR Battery Charge to low. Recharge battery.2C01 LOW BATTERY ERROR2

6. Table of Error Codes0003 For All of these Diagnostic Codes:01001-Turn OffKey switchand disconnect batteri s.01001Turn Off Key switch and disconnect

Contents1 Cautions ----------------------------------------------------------------------Page 42 Maintenance Intervals ------------------------------

6. Table of Error Codes3212 For All of these Diagnostic Codes:3213 1- Turn Off Key switch and disconnect batteries. 3214 2- Wait 1 minute.3- Reconnec

5.1 Table Error Codes (LED)Single flash Low Batteries-ChargeSingle flash Low Batteries-Charge the batteriesSingle flash Traction drive motor disconnec

5.1 Table Error Codes (LED)Single flash–Vacuum motor disconnectedSingle flash –Vacuum motor disconnected Single flashOff Isle Wand ActivatedSingle fla

5.1 Table Error Codes (LED)Single Flash- Solution tank em t - Riders onlygpyyTwoNot usedTwo flash-Not usedTh fl hThree flash-Water solenoid faultFour

5.1 Table Error Codes (LED)Single flash-High battery voltage-Check all connectionsSingle flash-High battery voltage-Check all connectionsRipple-Thrott

6. Side Squeegee Adjustment SCV2426 & SCV2832E OnlyCylindrical DecksThe side squeegees on the cylindrical decks can be adjusted by loosening the t

6.1 Side Squeegee Adjustment SCV2426 & SCV2832E OnlyDisk DecksThe side squeegee assemblies can be adjusted by loosening

7. Squeegee AdjustmentLater Models Onlyy• The pitch of the squeegee can be adjusted by turning th k b L th iWing Nutsthe knob. Loosen the wing nuts b

7. Rear Squeegee Adjustment Later Models OnlyPage 28

7. Rear Squeegee AdjustmentLater Models OnlyyPage 29

Contents5.4 Error Codes (LED) --------------------------------------------------------------6 Side Squeegee Adjustment (cylindrical) -----------------

8. Replacing the Brush Actuator on the SCV 28 or 32All Versions Of SCV2832E and SC280000Replacing the Brush Actuator on the SCV 28 or 321. Lower the b

8. Replacing the Brush Actuator on the SCV 28 or 32All Versions Of SCV2832E and SC28000016. Slide the brush deck into position, install the four moun

8.1 Actuator AdjustmentPage 32

8.2 Entering Service Mode with a Stuck Actuator Page 33

9. Trouble Shooting the Code 8 ErrorES2832,CP2832,SCV2426andSC2832EModelsOnly)1. Check for loose or burnt connections on the controller, batteri

9. Trouble Shooting the Code 8 Error6. Disconnect one motor connector from the Trio controller at a time and disconnect the batteries for 1 minute and

10. Testing the Throttle Potentiometer1. The throttle potentiometer resistance can be measured with an ohmmeter.2. Unplug the throttle potentiometer a

10. Testing the Throttle Potentiometer8. If they do not find a problem here, have them retest at the connector at the Triocontroller. 9. Reconnec

11. Identifying the Cause of Trio Failures1. Check for loose or burnt connections on the controller, batteries, cables and the circuit breaker. Make

12. NotesPage 39

1. Cautions• Always disconnect the A.C. Cord from the outlet and and D.C. Cord from the battery pack before servicing the machine. Except for making

2. Maintenance Intervals•Maintenance Intervals: In a modular structure, the Minuteman System Maintenance determines the specific technical proceedure

2.1 Minuteman System Maintenance KPage 6

2.2 Minuteman System Maintenance IPage 7Page 7

2.3 Minuteman System Maintenance IIPage 8

2.4 Minuteman System Maintenance SPage 9 g