Minuteman E20 Bedienungsanleitung Seite 1

User ManualE17/E20 Walk-Behind ScrubberDisc Brush Drive

10Machine OverviewControl PanelABCDFEGA BAIL HANDLEB HANDLE ADJUSTMENT KNOBC KEY SWITCHD SQUEEGEE LIFT LEVERE SOLUTION CONTROL LEVERF BATTERY GAUGEG C

11Machine OverviewBail Handle(A) When the scrubdeck is lowered to the floor, the bail handle enables the brush motor and moves the machineforward once

12Machine OverviewOptional Hour MeterMinuteman offers an optional hour meter for theE17/E20. The optional kit replaces the power cordmounting bracket

13Machine OverviewABDCThe optional solution solenoid, which shuts off solution flow when the bail handle is released, is protected from debris by the

14Machine OverviewBattery CompartmentCircuit BreakersA Main Control Breaker - 4AB Brush Motor Breaker - 30AC Vacuum Motor Breaker - 20AThe circuit bre

15Machine OverviewABCDEE17 Rear SqueegeeA Adjusting Nut (6)B Squeegee Bumper Wheel (2)C Squeegee Casting AssemblyD Squeegee BladeE Squeegee Mounting B

16Machine OverviewRear SqueegeeA SqueegeeB Star-shaped knobC Adjusting screw for angle adjustmentD Suction hoseE Blade fastening latchF Washers for ca

17Machine OverviewThe angle adjustment is the decisive factor inensuring that the squeegee blades on thesqueegee lie evenly on the floor.1. Park the m

18Machine OverviewIf streaks are present, despite an optimumangle adjustment, the clearance between thecaster wheels and floor must be adjusted bychan

19Machine OverviewHandle AdjustmentThe E17/E20 handle was designed with operator comfort inmind. The angle and horizontal position of the handle can

2This manual is furnished with each new MINUTEMAN E17/E20. This provides the necessary operating and preventivemaintenance instructions. Operators mus

20Machine Overview123Plate Position 1(Shipping Position)Plate Position 2Plate Position 3(Fully Extended)Horizontal AdjustmentThe horizontal position c

21Machine OverviewThe solution tank may be drained by removing the Solution Tank DrainHose (A) from the Hose Barb (B) and routing the hose to a floor

22Machine OverviewThe Solution Fill Filter (B) should be cleaned regularly.To remove, simply open the Solution Tank Lid (A) andpull the filter out.ABS

23Machine OverviewScreened FloatIf the recovery tank (C) is overfilled or a large amount of foaming ispresent, the screened float (B) blocks the vacuu

24Machine OverviewScreened Float RemovalThe screened float is positioned between the vacuum manifold (A)and recovery tank (C). The screened float (B)

25Machine OverviewRecovery Tank Drain HoseTwist Cap to Open and Drain Twist & Lift cap to clean outlarge debrisDeck Skirt Removal(Do not lower wit

26Machine OverviewABDCThe solution solenoid, which shuts off solution flow when the bail handle is released, is protected from debris by the in-line f

27The E17/E20This machine was designed with total operator comfort and ease of use in mind. All machine components have been designed as a totalsystem

28Machine OperationTo Turn on MachineTurn key to operate position ( I )To Turn on VacuumLower squeegee into operate position, vacuum motor will turn o

29Machine OperationHour Meter (Optional)Hour meter will automatically record operating time of the brush motor.Solution Solenoid (Optional)Water solen

3Technical SpecificationsModel E17/E20Model No. E17BD / E17BDCE / E17BDQP / E17BDQPCEE17BDQPG / E17BDQPGCE / E17BDQPG-KTE20BD / E20BDCE / E20BDQP / E2

30Machine Operation1. To load the brush, first center theE17/E20 brush deck over thescrub brush.2. Lower the scrub deck by releasingthe deck lift peda

31Machine OperationUnloading Brush3. When done correctly the brushshould release from the scrub deckand fall to the floor.1. To unload the brush, firs

32Notes

33Notes

34After UseAfter Use1. When finished scrubbing, lift the scrub deck and turn the solution lever off. Lift the rear squeegee. Move the machineto a serv

35Have a qualified service technician check the vacuum motor carbon motor brushes once a year or after 300 operating hours.The brush motor and transax

36Problem Possible Cause Remedy Poor water pick-up Worn or torn squeegee blades Rotate or replace blades Recovery tank full Empty recovery tank

37TroubleshootingProblem Possible Cause Remedy Vacuum motor does not turn on Recovery tank full Empty recovery tank Excessive foaming in recove

38Minuteman International Made Simple Commercial Limited WarrantyREVISION F EFFECTIVE 6/1/2009Minuteman International, Inc. warrants to the original p

39Cord Electric Group: Three years parts, two years labor, ninety days travel (Not to exceed two hours)Exceptions……….Model Parts Labor Poly TravelPor

4CE Declaration

Minuteman International · 14N845 U.S. Route 20 · Pingree Grove, Illinois 60140 USAPhone 800-323-9420 · Fax 800-422-6933www.minutemanintl.comA Member

5Table Of ContentsAdjusting the E20 Squeegee Blades ... 17Angle Adjustment ...

6Safety InstructionsIMPORTANT SAFETY INSTRUCTIONSOperators must read and understand this manual before operating or maintaining this machine.Do not op

7InspectionCarefully unpack and inspect your E17/E20 Walk-Behind Scrubber for shipping damage. Follow unpacking instructions onshipping pallet. Each u

8Machine OverviewMachine Overview - FrontA CUP HOLDERB SOLUTION FILL PORTC RECOVERY TANK LIDD RECOVERY TANKE BRUSH DECKF FRONT WHEELG REAR CASTERH SOL

9Machine OverviewMachine Overview - RearA BAIL HANDLEB SQUEEGEE LIFT LEVERC SOLUTION CONTROL LEVERD RECOVERY TANK DRAIN HOSEE ONBOARD CHARGER CORDF CI